AKKUTEC 2420 3ph

DC-UPS with Batteries

Typ              :   AKKUTEC 2420-0 3ph
Art.-No.        :   NBPA0313G01002

Short description

The battery buffered DC power supply of the series AKKUTEC is working according the stand-by parallel mode and ensures in connection with a lead-acid accumulator a safe continuous DC power supply in case of mains failure.

The power supply has the following features:

  • Primary switched power supply with  I/U-charging characteristics
  • active power factor correction (PFC)
  • Battery management by micro-controller
  • Battery voltage tracking of the charging voltage by external sensor module (optional)
  • Display- and control panel for mount in cabinet door or module (optional)
  • redundant operation or Master-/Slave-operation possible

 

 

Technical Data

Nominal input voltage            3 x 400 - 500 V AC -15% +10%
Nominal frequency45 – 65 Hz
System voltage     24 V DC
Output voltage

(depending on state of Charge of the battery)

voltage range

- with temperature tracking

- without temperature tracking


 

 

19,8 V DC - 27,8 V DC

19,8 V DC - 26,8 V DC

Nominal utput current20 A at 100% ED
Protective systemIP 20

safe separation    (safe separation between input and output)

acc. EN61558-2-17
operational temperature0 - 40 °C
short circuit protectionelectronic, short-circuit-proof output
Batteryexternal
Battery fuseexternal
back-up time

depending on battery

charging characteristicsI/U DIN 41773 part 1
Opt. temperature tracking
boost Charge via control contact (up to 28,6V)

final charging voltage
without temp.- sensor     

with temp.- sensor at 25°


26,8 V DC ± 0,4%

27,8 V DC ± 0,4%

charging current at 100% load2 A
charging current at 0% load22 A

deep discharge protection

load rejection at battery voltage ≤ 19,8 V
LED-display

mains / battery operation 'Netz OK' LED green

General error  'Fehler' LED yellow
battery voltage within LED green
battery voltage above LED green

Relays-outputs

mains/UPS-operation  0,5 A /30 V DC

General error       0,5 A /30 V DC

voltage above    0,5 A /30 V DC

voltage within    0,5 A /30 V DC

control inputs referring to earth on +24VDCShut down
boost charge
Special features

active current share at Master – Slave respectively redundant Operation with CS bus

time function (load rejection after adjustable back-up time)

expandableIn 20 A steps Master/Slave
active PFCharmonic ripple at input according to EN 61000-3-2
PF ~ 0,99
Batterymanagement

Batterymanagement with internal micro controler,

battery circuit control

control battery circuit/battery fuse each 60 sec.

Real battery power measurement

battery load test during operation. (load of the battery with simultaneous voltage measurement) each 24h

EMI-regulations

EN 55011/ 1998 class A Group1

EN 50082-1/1.92

EN 50178

type of construction

module 
connection

primary

secondary Ua

Secondary batt

with terminals

2,5 mm²

6 mm²

4 mm²

dimensions101 x 241 x 244 mm (B x H x T)
weight

2,6 kg

Options
control and Display panel

well readable, 20-digit, 2-line Alpha numeric LC-Display with back-ground illumination

separate possible adjustements for contrast and brightness

supply and data Transfer with 2 wire bus, thus low wiring activity necessary  

reading and writing of charging and control parameters

display of status messages in plain text

acoustic Signal for warnings respectively Errors (deactivatable)

possibility of Display of the operational data,  for redundant systems also with only one Panel possible.  

easy user prompting

3-button operation

protection of functions by Password Levels

suitable for built in cabinet door (protective system IP54)

Temperature tracking with temperature sensor at terminal strip IO-1 and 2 the charging voltage is automatically adjusted to the environmental conditions (26,8-27,8 V). Overtemperature at the batteries (above 45°C) is displayed and announced.

Shut-down

Abort of the UPS - operation

potentialfree gate input

Switch level: 24 V DC (6-45 V DC)

UL approvalsNo
 
For more details see datasheet.

Downloads

Description
Version
File Format

Datasheet

160803PDF
Quickstart AKKUTEC 2420-0 3ph.  + NBBH 2407-PDF
Manual130926PDF
EPLAN Macro140703edz
3D-Model160822STP

To download the manual, the EPLAN Macro and the 3D-Model please log in here